Reviews Living

It took days of going through more than a thousand customer reviews and conducting expert researches to narrow down the list. Weve included a comparison table below to give you a quick summary of our top 10 bme280 i2c. Its followed by an in-depth review of each bme280 i2c. Hopefully, once you are done reading this article, you will be well informed about bme280 i2c and be able to select the right bme280 i2c for you without any hesitations.

Related posts:

Best bme280 i2c reviews

1. AITRIP 3pcs BME280 Compatible with BMP280 Digital 5V Temperature Humidity Sensor Atmospheric Barometric Pressure Board IIC I2C Breakout for Arduino

Feature

Supply Voltage: 1.8 - 5V DC
Interface: I2C (up to 3.4MHz), SPI (up to 10 MHz)
BME280 5V barometric pressure digital sensor, is a new chip which was originally designed for the next generation of smartphones
BME280 is the precision sensor, is soldered onto PCB
It uses both I2C and SPI (supports 3-, 4-wire SPI) interface

2. Taidacent Outdoor 3.3V 5V IIC I2C Digital Temperature Humidity Atmospheric Barometric Air Pressure Sensor Probe BME280 (1m, Black)

Feature

The BME280 sensor is great for all sorts of weather sensing and can even be used in both I2C and SPI! For simple easy wiring, go with I2C. If you want to connect a bunch of sensors without worrying about I2C address collisions, go with SPI.
Our BME280 Sensor is the best low-cost, precision sensing solution for measuring barometric pressure with 1 hPa absolute accuraccy, and temperature with 1.0C accuracy. Because pressure changes with altitude, and the pressure measurements are good, you can also use it as an altimeter with 1 meter accuracy.
Supply Voltage: 1.8 - 5V DC Interface: I2C (up to 3.4MHz), SPI (up to 10 MHz)
Temperature: -40 to +85C Humidity: 0-100% Pressure: 300-1100 hPa
Temperature: 0.01C Humidity: 0.008% Pressure: 0.18Pa

3. Adafruit BME280 I2C or SPI Temperature Humidity Pressure Sensor

Feature

BME280: an environmental sensor with temperature, barometric pressure
Great for all sorts of weather sensing and can even be used in both I2C and SPI!
Low altitude noise of 0.25m and the same fast conversion time compared to BMP085/BMP180/BMP183

4. ACEIRMC BME280 Digital 5V Temperature Humidity Sensor Atmospheric Barometric Pressure Board IIC I2C Breakout for Arduino (Pack of 2)

Feature

1.This Kit contains with 3pcs of digital sensor module, which can be independently enabled / disabled, which can measure not only the temperature humidity, but also the pressure.
2.The BME280 sensor is great for all sorts of weather sensing and can even be used in both I2C and SPI! For simple easy wiring, go with I2C. If you want to connect a bunch of sensors without worrying about I2C address collisions, go with SPI.
3.Our BME280 Sensor is the best low-cost, precision sensing solution for measuring barometric pressure with 1 hPa absolute accuraccy, and temperature with 1.0C accuracy. Because pressure changes with altitude, and the pressure measurements are good, you can also use it as an altimeter with 1 meter accuracy.
4.Organizer BME280 Atmospheric Pressure Sensor Temperature Humidity Sensor Breakout for Arduino
5.Package 2pcs BME280 Atmospheric Pressure Sensor Temperature Humidity Sensor Breakout

5. Onyehn BME280 Temperature Humidity Barometric Pressure Sensor Module with IIC I2C for Arduino(Pack of 2pcs)

Feature

BME280 is a precision sensor, is soldered onto PCB.
Not only the pressure and the temperature, this sensor can measure humidity.
It uses both I2C and SPI (supports 3-, 4-wire SPI) interface.
With an I2C connection you have access to enough weather data to make some pretty good predictions for your local area.
It is made up of a very accurate pressure sensor and an associated temperature sensor which helps calibrate the pressure readings.

6. HiLetgo BME280 3.3V Atmospheric Pressure Sensor GY-BME280-3.3 Temperature Humidity Sensor Module for Arduino

Feature

Supply voltage VDD main supply voltage range: 1.71 V to 3.6 V
Interface: I2C (up to 3.4MHz), SPI (up to 10 MHz)
Temperature: -40 to +85C
Humidity: 0-100%
Pressure: 300-1100 hPa

7. Waveshare BME280 Environmental Sensor Temperature Humidity Barometric Pressure Atmospheric Pressure Support I2C and SPI Interface Compatible with 3.3V/5V Voltage Levels

Feature

A tiny sensor breakout with BME280 onboard, sensing environmental temperature, humidity, and barometric pressure. It supports both I2C and SPI interfaces, also is compatible with 3.3V/5V voltage levels. Due to its ultra small form factor, low power consumption, high precision with stability, the BME280 Environmental Sensor is suited for applications such as environment monitoring, weather forecast, altimeter, and IoT projects, and so on.
Supports I2C (default), configurable slave address. Supports SPI, switch to SPI via I/O setting.
Temperature sensing: -40~85C (resolution 0.01C, accuracy 1C). Humidity sensing: 0~100%RH (resolution 0.008%RH, accuracy 3%RH, response time 1s, delay 2%RH). Barometric pressure sensing: 300~1100 hPa (resolution 0.18Pa, accuracy 1hPa).
Power consumption: <0.1mA@1Hz (H,P,T). Dimension: 27mm x 20mm. Mounting hole size: 2.0mm.
Onboard voltage level translator, compatible with 3.3V/5V operating voltage. Comes with development resources and manual (examples for Raspberry Pi/Arduino/STM32).

8. Waveshare BME280 Environmental Sensor, Temperature, Humidity, Barometric Pressure Detection Module I2C/SPI Interface for Weather Forecast, IoT Projects, ect

Feature

Supports I2C (default), configurable slave address, supports SPI, switch to SPI via I/O setting
Onboard voltage level translator, compatible with 3.3V/5V operating voltage
Humidity sensing: 0~100%RH (resolution 0.008%RH, accuracy 3%RH, response time 1s, delay 2%RH)
Temperature sensing: -40~85C (resolution 0.01C, accuracy 1C),barometric pressure sensing: 300~1100 hPa (resolution 0.18Pa, accuracy 1hPa)

9. SparkFun Atmospheric Sensor Breakout - BME280 Measure Weather with Barometric pressure Relative Humidity Temperature Small Footprint I2C & SPI Communications Interface Operating Voltage 3.3V Low Power

Feature

Temp Range: -40C to 85C - Humidity Range: 0 - 100% RH, =-3% from 20-80%
Pressure Range: 30,000Pa to 110,000Pa, relative accuracy of 12Pa, absolute accuracy of 100Pa
Altitude Range: 0 to 30,000 ft (9.2 km), relative accuracy of 3.3 ft (1 m) at sea level, 6.6 (2 m) at 30,000 ft.
Selectable I2C addresses through a jumper on the back of the door. Pull-ups for both I2C and SPI.
Solder your headers or connectors of choice to connect it to your microcontroller or project.

10. diymore 2pcs BME280 5V Temperature Humidity Sensor Atmospheric Barometric Pressure Sensor with IIC I2C Breakout

Feature

Not only the pressure and the temperature, this sensor can measure humidity.
Make sure to put SDO to high to get address 0x77. This will work with Adafruit BME280 library perfectly.
BME280 is a precision sensor, is soldered onto PCB. It uses both I2C and SPI (supports 3-, 4-wire SPI) interface.
With an I2C connection you have access to enough weather data to make some pretty good predictions for your local area.
It is made up of a very accurate pressure sensor and an associated temperature sensor which helps calibrate the pressure readings.

Conclusion

All above are our suggestions for bme280 i2c. This might not suit you, so we prefer that you read all detail information also customer reviews to choose yours. Please also help to share your experience when using bme280 i2c with us by comment in this post. Thank you!