Reviews Living

Finding the best gps module arduino suitable for your needs isnt easy. With hundreds of choices can distract you. Knowing whats bad and whats good can be something of a minefield. In this article, weve done the hard work for you.

Related posts:

Best gps module arduino reviews

1. GPS Module GPS NEO-6M(Ar duino GPS, Drone Microcontroller GPS Receiver) Compatible with 51 Microcontroller STM32 Ar duino UNO R3 with IPEX Antenna High Sensitivity for Navigation Satellite Positioning

Feature

How to Use This Module, Important information: https://drive.google.com/open?id=1dSdSLoo4JpHFd8qM0BEkE5fvYLP2yZlh; Manual: https://drive.google.com/open?id=15cIa03wqNB7sItn6I2s5xZ8PGOZ1Q0JF;
Note: This GPS module will not search for signals when the weather is bad, and it will not search for stars indoors. When using it, please make sure that the GPS module is in an open location.
GPSBaud needs to be set to 9600 instead of 4800; PPS pin is not needed unless using the GPS to drive a hardware high precision clock; GT-U7 main module GPS module using the original UBLOX 7th generation chip, Software is compatible with NEO-6M. GT-U7 module, with high sensitivity, low power consumption, miniaturization, its extremely high tracking sensitivity greatly expanded its positioning of the coverage.
With a USB interface, you can directly use the phone data cable on the computer point of view positioning effect; With IPEX antenna interface, the default distribution of active antenna, can be quickly positioned.
USB directly connected to the computer, That is, with the host computer-owned serial port function, no need for external serial module, send IPX interface active antenna!

2. Gowoops GPS Module with TTL Ceramic Passive Antenna for Arduino Raspberry Pi 2 3 B+ MCU

Feature

This is a small size item, and it has excellent performance. This item has data backup battery and LED signal indicator.
Comes with 25 x 25mm ceramic passive antenna, strong star search ability.
Various parameters can be set via the serial port, and can be stored in the EEPROM, easy to use.
Compatible with 3.3V / 5V level, convenient for connection to a variety of microprocessor systems.
Built-in rechargeable backup battery, you can keep the ephemeris data when power down.

3. HiLetgo GY-NEO6MV2 NEO-6M GPS Flight Controller Module 3V-5V with Super Strong Ceramic Antenna for Arduino EEPROM APM 2.5

Feature

Module with a ceramic antenna, superior signal
Save the configuration parameter data EEPROM Down
With data backup battery;With LED signal indicator
Default baud rate: 9600, Interface: RS232 TTL
Compatible with a variety of flight control module

4. Adafruit Ultimate GPS Breakout - 66 channel w/10 Hz updates [ADA746]

Feature

-165 dBm sensitivity, 10 Hz updates, 66 channels
5V friendly design and only 20mA current draw
Internal patch antenna + u.FL connector for external active antenna
Built-in datalogging
Perfect for Raspberry Pi, Arduino and more!

5. DIYmall 6M GPS Module with EEPROM for MWC/AeroQuad with Antenna for Arduino Flight Control Aircraft

Feature

When you test the GPS module, pls kindly note that you need test it in outdoor wide plain place, not indoor.
Document link: https://engineersportal.com/blog/2018/5/9/comparing-iphone-gps-against-neo-6m-gy-gps6m-gps-module-with-arduino
Youtube link: https://www.youtube.com/watch?v=VziqwqLaGso
LED signal indicator,With data backup battery
EEPROM power down to save the configuration parameters data

6. Gowoops GPS Module with 3m Active Antenna for Arduino STM32 51 Single Chip Microcomputer

Feature

1. With micro USB port, you can use general mobile phone cable to connect the GPS module to your computer. Do not need USB-TTL, convenien for use.
2. The GPS module has ceramic passive antenna, you can search the satelite in a open area, do not need the external antenna.
3. With SMA port, convenient for connect with the 3m Active Antenna, stronger satelite search ability.
4. With the reserved TTL port, covenient for connect to USB-TTL or external single chip microcomputer.

7. BN-180 GPS Module UART TTL Dual Glonass GPS Car Navigation + GPS Antenna for Arduino Raspberry Pi Pixhawk Aircraft CC3D F3 Flight Controller Geekstory

Feature

This BN-180 GPS Module can show your speed. When you use it for Raspberry Pi, there is no driver needed. Here is connection with RPi, red to 3.3v, black to gnd, green to txd, white to rxd.
The TX LED flash means gps module output normally. The PPS LED flash means gps module locate your place.
Data Level : TTL or RS-232, Default TTL level. To make it be RS232 output, you need to use one TTL to RS232 converter cable.
This BN-180 GPS Module does not have FLASH and cannot be saved. 72 Searching Channel Support Rate : 4800bps to 921600bps, Default 9600bps.
What you will get: 1 X BN-180 GPS Module

8. Ximimark NEO-7M UBLOX GPS Satellite Positioning Module with SMA Antenna Interface for Arduino STM32 C51 Replace NEO-6M 3.3V/5V Power Supply 1Pcs

Feature

Get 51 Arduino STM32 microcontroller routine.
with a USB interface, you can watch the computer positioning effect directly phone line.
with the passive ceramic antenna and passive antenna amplifier, make better use of the individual effects.
with SMA interface can be directly connected to an active antenna SMA.
TTL level, compatible with 3.3V/5V systems.

9. HiLetgo NEO-7M GPS Satellite Positioning Module for Arduino STM32 C51 Replace NEO-6M 3.3V/5V Power Supply

Feature

1.Get 51 Arduino STM32 microcontroller routine.
2.With a USB interface, you can watch the computer positioning effect directly phone line.
3.With the passive ceramic antenna and passive antenna amplifier, make better use of the individual effects.
4.With SMA interface can be directly connected to an active antenna SMA.
5.TTL level, compatible with 3.3V/5V systems.(Size:39*25.5mm)

10. GPS Module Receiver,Navigation Satellite Positioning NEO-6M (Arduino GPS, Drone Microcontroller, GPS Receiver) Compatible with 51 Microcontroller STM32 Arduino UNO R3 with Antenna High Sensitivity

Feature

Product Instruction:https://www.youtube.com/watch?v=bgOZLgaLa0g. Library: http://arduiniana.org/libraries/tinygpsplus/. The easiest way to use the GPS module is to use TinyGPSPlus library: https://github.com/mikalhart/TinyGPSPlus/releases; Manual: https://drive.google.com/open?id=15cIa03wqNB7sItn6I2s5xZ8PGOZ1Q0JF; GPSBaud needs to be set to 9600 instead of 4800; PPS pin is not needed unless using the GPS to drive a hardware high precision clock;
With a USB interface, you can directly use the phone data cable on the computer point of view positioning effect; With IPEX antenna interface, the default distribution of active antenna, can be quickly positioned.
GT-U7 main module GPS module using the original UBLOX 7th generation chip, Software is compatible with NEO-6M. GT-U7 module, with high sensitivity, low power consumption, miniaturization, its extremely high tracking sensitivity greatly expanded its positioning of the coverage.
USB directly connected to the computer, That is, with the host computer-owned serial port function, no need for external serial module, send IPX interface active antenna!
If you have any issue when using our product,or you need product use documentation please contact us directly for assistance.we will reply your problem in 24 hours.We try our best to provide the most professional service for each customer.

Conclusion

All above are our suggestions for gps module arduino. This might not suit you, so we prefer that you read all detail information also customer reviews to choose yours. Please also help to share your experience when using gps module arduino with us by comment in this post. Thank you!